I am currently in the market for some wireless access points and thought I’d get some suggestions here first. I am currently using some old eero pro’s as access points with a firewalla router. The firewalla isn’t old and I am happy with it so I am not looking to replace it with something at this time.
Are there suggestions for more privacy focused networking equipment? Or is that just a dumb question to ask?
Sorry for asking, but what even is the use of having a Wireless Access Point? If you have a router then you should be all set, no?
Take this with a major grain of salt as I don’t know much about this. I think that a router isn’t always also a wireless access point. It could just be for wired connections like a switch. Please downvote and correct me if I’m wrong, I really know little about this.
A router bridges your local network and the internet. It decides where to send packets. Typically in residential installations, the router acts as a gateway, acts as a local DHCP server, acts as a DNS server. Kind of all in one.
A access point is a wireless device, which talks to wireless clients, putting their traffic on the network.
Again residential devices, tend to be all in one, everything you would expect in your router/gateway, and an access point.
This is fine for small installations, or people who don’t really care particularly about quality. When you get into dedicated devices, you get higher reliability in your access points, better radios, better firmware. They keep it simple stupid philosophy applies to hardware as well.
If you have a large house, you’ll probably need multiple access points to cover the entirety of the house, and you wouldn’t want each access point to be acting as a gateway, a router, or a DHCP server.
So it’s just like mini routers just dedicated to internet, with better quality and reliability, that connect to the main router when it’s near, but give you a stronger signal?
deleted by creator
Router is a technical term, that many people misuse due to retail advertising.
A router by itself has multiple networks that talks to, and decides what traffic goes to which network.
A switch has one network, but it’s aware of what device is attached to which port, and only forwards packets to the correct port for the device.
The difference between a router and a switch is what level of the network stack they’re working at. But basically switches are dumb and fast, routers are smarter and slower. A fast router tends to be expensive.
Wireless access points typically don’t want to send all of the wired network traffic over the wireless, if it’s not addressed to a wireless client, so it’ll keep track of the hardware address of the clients, and if it sees traffic destined for that hardware then and only then will it switch the packet onto the wireless network. Hence all access points tend to act as a hardware switch.
Let’s say you have a 10 room concrete building. Let’s say the concrete has rebar in it, so basically a wireless signal can’t go between rooms. This is theoretical, just go with me.
If you wanted to have seamless wireless access across the entire house, so that you could take a voice call and walk around. You would need to put a wireless access point in each room.
In order to allow seamless transfer between access points, you would probably want to have access points from the same vendor, all configured using the same network ID, using the same authentication scheme. That way your smarter clients like modern cell phones, would see that oh there’s multiple wireless access points in this network that I can talk to right now, I’ll switch from one to the other. When the switch happens you tend to lose some packets, so the faster the switch, the more seamless the experiences for people.
Some wireless access points can negotiate with each other to push specific clients to different access points. But most of this fast switching is done client side.
so in this 10-room building, you’re going to have 10 access points, you’re going to have a single router between the building and the internet, you’re going to have a DHCP server internally usually. Those access points may be negotiating between themselves, using some mesh technology, but ideally they’re all wired to the same network.
When a client switches from access point a to access point b, those access points will now know that physical hardware address has switched, and the main network should still send the packets to the client with very few being dropped.
I think the Firewalla may be able to broadcast WiFi (I’m not sure) but it doesn’t matter much to me because it’s tucked away in my utility room. I need a couple AP’s for my upstairs for all my wireless devices.
More control. I can make a homemade PFSense router that gives me enterprise grade features like VLANS, VPN options and advanced firewall rules.
Performance. A dedicated AP from Unifi or Armada is more powerful and stable than most consumer wireless routers.
Price. Building a decent setup yourself actually pretty cost effective compared to high-end consumer routers.
It’s DEFINITELY NOT for everyone, but if you’re a nerd with some networking skills and time to spare you can make a baller enterprise-grade home network for under $300. My budget setup made from used components blows any $500 “premium” router away.