For the first time I am actually switching my main PC from Windows to Linux.

Problem: When booting into Fedora there was no display output, I changed it to safe graphics to install everything and that fixed it but after the install finished I tried turning it back off and there was still no display output

What I have already tried: I’ve tried installing drivers and everything I could find although that shouldn’t be the problem since I have an AMD 6700xt and Fedora comes with AMD drivers built in. I also tried Installing Linux Mint thinking maybe the distro was the problem but it came up with the same issue.

And if anyone suggests it no there is no way I am going to daily drive on safe graphics.

Edit: I am dual booting on a single 500gb ssd with windows already installed on the other half of the drive, not sure if that would be the problem. Also a similar problem was happening on windows if I left the screen in login for too long without signing in the display would show no signal and it wouldn’t wake up if I moved my mouse or clicked or pressed any keys.

  • azvasKvklenko@sh.itjust.works
    link
    fedilink
    English
    arrow-up
    2
    ·
    2 days ago

    My bet is it tries to default to mode that your display doesn’t like, probably because of some wrong info in monitor’s EDID downloaded from the connector, but that’s just my guess.

    Before booting, use key e on grub menu, locate line where there is initrd to pass boot parameters. You can force modes using video= parameter, and you can also replace/modify your EDID. Refer to section # Forcing modes and EDID on this page: https://wiki.archlinux.org/title/Kernel_mode_setting

    These changes can also be achieved permanently by editing /etc/default/grub and regenerating its configuration, in case you use grub.

    Easiest would be to have separate extra monitor temporarily or another computer to connect over SSH, but if those low “safe” graphics modes work, that can probably do also.

  • CaptainBasculin
    link
    fedilink
    arrow-up
    4
    ·
    3 days ago

    Try switching to X11, see if the issue persists.

    Also which screen size options does your monitor see? In my experience it could act problematic with high refresh rate 4K displays, try reducing them until it feels fine.

    • pineappleOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      2 days ago

      In safe graphics my resolution is locked on 1024*768 at 60hz, I have a 1080 144 hertz monitor.

      And it looks like changing to x11 didn’t fix anything.

    • pineappleOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      2 days ago

      amd ryzen 5 1600 cpu amd radeon 6700xt gpu 16gb ddr4 3200 ram 500gb wd blue sata ssd aoc 24g2 monitor

      • Domi@lemmy.secnd.me
        link
        fedilink
        arrow-up
        1
        ·
        edit-2
        2 days ago

        You should have absolutely no issues with that hardware on Fedora.

        Could you try switching the display cable out? If that doesn’t work, try switching the cable to a different type (e.g. DisplayPort instead of HDMI or vice versa). If that also doesn’t work, try with a different display if you can.

  • eldavi
    link
    fedilink
    arrow-up
    2
    ·
    3 days ago

    Do you see any errors/failures/timeouts/etc in the logs when you use journalctl?

    • pineappleOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      2 days ago

      Yeah there are a lot although I would still consider myself a beginner at Linux and the terminal so I’m not really sure what the logs mean and which ones specifically I should be looking for.

      • eldavi
        link
        fedilink
        arrow-up
        2
        ·
        edit-2
        2 days ago

        unless you’re using a very old or niche distribution, all of your logs are centralized in to a single space and the command journalctl will let you look at them.

        in your situation i would use the command journalctl -f to get a live action printout of all the things that are happening as you try to start your x server and you can look through them to find messages in the logs that contain something like “failure” or “error” or “timeout” to find clues as to what’s causing your problem.

        you don’t need the xserver to run linux and most distributions give you 7 virtual terminals that you can log into without the xserver and each one can be accessed using the keyboard combinations alt+crtl+f1 through alt+crtl+f7.

        when i used to be in situations like yours i would log into two virtual terminals. i would use one of them to run tail -f $logname and the other to start the xserver. tail -f $logname is the older deprecated version of journalctl -fand they both show you what’s happening in your computer as it occurs. you’ll likely only need to see it once or twice to get a sense of what’s happening and what the interval looks like and you can accomplish something similar if you keep track of your own timestamps by hand and then look through the logs searching for those timestamps in the logs.

        share the log messages with errors/failures/timeout/whatever in them and we can both look for clues using google or ai.

    • pbjamm@beehaw.org
      link
      fedilink
      English
      arrow-up
      2
      ·
      3 days ago

      Fore sure more details needed. I run LMDE6 on my system and its RX7600 works perfectly out of the box.
      currently kernel 6.10

      • pineappleOP
        link
        fedilink
        English
        arrow-up
        1
        ·
        2 days ago

        Could you tell me what information you need?

  • IsoSpandy@lemm.ee
    link
    fedilink
    arrow-up
    1
    ·
    3 days ago

    After booting in, switch to a tty, then start the de from there, so like I use plasma so I execute plasma-wayland. Check if that works, if so, then the problem lies with the login manager (sddm or gdm). If not post the error log and I will check if I can understand what’s wrong.

  • I_Miss_Daniel@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    3 days ago

    Does your system have two graphics processors? One of my laptops won’t work with many distros as they boot to blank screens after install. Fedora was one that does work in my case.

    It’s a laptop with two GPUs.

    • pineappleOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      2 days ago

      No it only has the 6700xt no integrated graphics either so I can’t even test that. I might be able to borrow my friends 3050 for troubleshooting. Although I would still need the 6700xt working even if the 3050 fixes the issue.