First of all, I’m sorry if this isn’t the best place to post this; but I’m not aware of any more general tech support / PC building / ASUS forums here that I could post this to instead.

I’m trying to turn an old PC of mine built around an Asus M5A78L-M PLUS/USB3 into a home server, part of which means I’d like to have the two 6TB harddrives I’ve installed in it in a RAID 1 array. The manual, which I found a copy of online, briefly mentions that it supports RAID 0, 1, and 10 for drives in ports 1-4, then says to look for more information in the “RAID/AHCI Supplementary Guide” in the support DVD, which I don’t have and can’t find online. In the “SATA Configuration” section of the BIOS, I set the “SATA Port1 - Port4” setting from “[IDE]” to “[RAID]”, which caused an additional step to start happening in the boot process where something labeled “RAID Option ROM Version 3.0.1540.39” by AMD would scan my drives for several seconds, then show some information on them and prompt me to press control+F to enter a “RAID Option ROM Utility”. When I do that it takes me to another screen with 4 options: “View Drive Assignments”, “Define LD”, “Delete LD”, and “Controller Configuration”. I go to “Define LD” and it lets me select 1 of 10 slots, and when I select one it allows me to choose its RAID mode from RAID 0, RAID 1 RAID 10, JBOD, or “RAID READY”, allows me to change its “Stripe Block” (64 KB or 128 KB for 0 & 10, NA for others), its “Fast Init” (On or Off for all options) its “Gigabyte Boundary” (On or off for the RAIDs, NA for JBOD and “RAID READY”), and shows its “Cache Mode” (“WriteThru” for all except JBOD, which is NA), and gives me a list of all my SATA hard drives and allows me to pick which whether its “Assignment” is N or Y. I set “RAID Mode” to RAID 1, leave Fast Init and Gigabyte Boundary as On, add both drives to the LD and press control+Y to save. It asks me to confirm I’m okay with all the data on the drive being wiped, then gives me an option to choose the LD size manually or choose the biggest available size, which I do. After a few seconds I’m taken back to the Define LD Menu, with an entry in slot #1 - “RAID Mode” is listed as RAID 1, “Total Drv” is 2, “Capacity(GB)” is 1602.95, and “Status” is Functional. No extra prompts are given and everything seems mostly fine. As far as I can tell, the array is set up.

I insert my Linux Mint Installation livedisc and reboot. I open Gnome Discs. it’s still showing both discs independently, with no third 6TB drive nor any ~1.6TB drive. I open GParted. It shows both discs independently. I start the Install Linux Mint utility. Once I get to the appropriate part, it’s detecting exactly two hard drives, both 6TB. Every other Linux installer I’ve tried (Debian, OpenMediaVault, Fedora Server) have detected two separate drives and no Raid anything. The two HDDs are connected to SATA ports #3 and #4. I’ve never set up any sort of RAID array before, and don’t know enough about anything to know what exactly I’m doing wrong here. Can anyone help me figure out what the problem is?

  • SuperiorOne
    link
    fedilink
    English
    arrow-up
    13
    ·
    1 year ago

    The RAID on your motherboard is a mess and you should avoid it like the plague. — Wendell from Level1Tech

    Creating RAID with either zfs or btrfs is much more easier and they perform better than motherboard’s RAID implementations. If you want a UI, you can even install TrueNAS Core as a server and manage zfs pools, share on network etc.