• Omnomnom-oom@kbin.social
      link
      fedilink
      arrow-up
      16
      ·
      1 year ago

      That is actually a feature of this design. They were the answer to in-line screwdrivers who had no precise stopping torque: cam-out before the thread is damaged.

      • buckykat@lemmy.fmhy.ml
        link
        fedilink
        arrow-up
        20
        ·
        1 year ago

        I know it’s an intentional feature, but it’s a bad feature. Camming out damages the head of the screw. This exchanges repairability for manufacturing simplicity. Additionally, the sloped shape makes it possible to use slightly oversized or undersized drivers, further increasing the chance of camming out and damaging the screwhead.

    • YouShutYoMouf@lemmy.fmhy.ml
      link
      fedilink
      arrow-up
      13
      ·
      1 year ago

      Square is really good too.

      Phillips and flat head bits fit in a variety of sizes of screw heads. We seem to have chosen convenience over performance.

      • motorwerks@sopuli.xyz
        link
        fedilink
        arrow-up
        3
        ·
        1 year ago

        If memory serves me correctly square drive is patented, & thus requires licensing, which is why it’s less commonly used.

      • yimby
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Pozidrive is a massive upgrade, if only people didn’t confuse it for Philips all the time

    • deten@lemmy.world
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      This is the way. Also I’m new to Lemmy so forever will this be how I start my experience here.

      Torx is hands down better in every way than flathead and Phillips.

  • MyFeetOwnMySoul@lemmy.ca
    link
    fedilink
    arrow-up
    35
    ·
    1 year ago

    Anyone who willfully uses a slotted screw on a new project in the presence of even somewhat reasonable alternatives should have a lifetime ban on designing any items for anyone.

    Also, use Robertsons, gink.

    • PupBiru@kbin.social
      link
      fedilink
      arrow-up
      18
      ·
      1 year ago

      it’s single valid use: somewhere that you may not have tools but might require an impromptu fix… preferably paired with a much larger screw than technically required so you can use things like coins as a driver

    • cannedtuna@lemmy.world
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      Fuck electrical wall plates I guess then? It’s so hard to find any switch plates or device plates that come with Phillips instead of Slotted.

    • nameisnotimportant
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      security torx

      Do you know what’s the deal with them except having to pay / find extra bits?

        • Taxxor@lemm.ee
          link
          fedilink
          arrow-up
          2
          ·
          edit-2
          1 year ago

          Most of the sets I own have a hole in them, so I think for the scenario that the average person does actually have a torx set, the chance is pretty high that it’s also one that they can use on those “security” torx screws. So I don’t see them that much more secure than regular torx. The only reason I could think of is that you also can use a normal screwdriver to unscrew a torx, which is harder to do with that extra pin. But it can still be done^^

          • SpookySnek@sh.itjust.works
            link
            fedilink
            arrow-up
            1
            ·
            1 year ago

            It used to be more secure but manufacturers started to just put a hole in all of their torx bits to compensate lol. Now it’s pretty much pointless

      • CaptainLemmit@feddit.it
        link
        fedilink
        arrow-up
        7
        ·
        edit-2
        1 year ago

        If you’re determined enough you can jam a slot screwdriver in a torx and turn it, the security bit makes it so that you have to be REALLY determined when you jam the slot screwdriver in

        • nameisnotimportant
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          Ha I like your spirit! Fortunately I have some at home and had only one occasion to use them thankfully

  • ArumiOrnaught@kbin.social
    link
    fedilink
    arrow-up
    23
    ·
    1 year ago

    I strongly dislike how many times I’ve stripped a Phillips and used a die grinder to force it to become a flat. Torx is fine.

    • Sir_Osis_of_Liver@kbin.social
      link
      fedilink
      arrow-up
      7
      ·
      1 year ago

      I used to restore “barn bikes”, most of them were Japanese. It took me a while to figure out the difference between Japanese Industrial Standard (JIS) and Phillips screws. Of course over the years, a lot of the fasteners had already been cammed out by previous owners using a Phillips screwdriver in a JIS screw. I had to resort to the die grinder method far more than I’d have preferred.

  • AClassyGentleman
    link
    fedilink
    arrow-up
    22
    arrow-down
    1
    ·
    1 year ago

    Situation: There are 20 screw standards.

    John Corporate: “20 standards… I know, I’ll create a new type of screw that will be unique to my corporate overlords and prevent users from repairing their own devices!”

    Situation: There are 21 screw standards.

    • barsoap@lemm.ee
      link
      fedilink
      arrow-up
      11
      ·
      edit-2
      1 year ago

      Torx are the better hex as they apply torque to six planes, not six lines. It’s right-out impossible to strip a torx.

      The disadvantage is that it’s harder to machine but that really doesn’t matter for cast screws. Tools are also cheaper that’s why IKEA etc. use them.

      • JohnDClay@sh.itjust.works
        link
        fedilink
        arrow-up
        2
        ·
        1 year ago

        Torx tools are cheaper? I didn’t know that. I’ve never really come across them, so I didn’t think they were an option for universal replacement.

        • barsoap@lemm.ee
          link
          fedilink
          arrow-up
          2
          ·
          1 year ago

          Nah, cheap hex tools are cheap, those one time use allen wrenches. Torx comes with a higher minimum quality as you can’t just bend some rolled hex stock and have something that passes as a tool.

          High-grade bits are expensive in either case, shape doesn’t matter much in that segment so tradespeople go by what’s the best shape and that’s torx. Really makes a difference when you’re going through thousands of say drywall screws a day: They never cam out, you can set precise torque with an actual torque limiter and screw them in at ridiculously high speeds without pressing down on the screw. Aim, fire, done, next, especially if your whatsitcalled in English has a magazine.

          (if you over-torque a torx screw one of two things is going to happen: Either the screw head breaks off, or the bit. Also a kind of torque limiter)

          In other applications they might be overkill but only having one type of screw around makes up for the minimal amount that torx is more expensive.

          Things like external hex or if you want squares or really whatever of course also have their place, no matter the even number of sides it’s all wrench flats.

          And for some reason electricians are fond of their combined flat/pozi screws. First outlet manufacturers used flatheads, then when switching to pozi they realised that while J. Random Consumer might have pozi screwdrivers their one insulated one is a flathead so they combined the shapes, then along come electricians and buy screwdrivers for that combined shape because it self-centres and nearly self-rotates and doesn’t cam out easily.

  • Welder@lemmy.ca
    link
    fedilink
    arrow-up
    18
    ·
    1 year ago

    Square is called a Robertson and is the standard for construction in Canada. None of that bullshit Phillips trash.

    • danwardvs@sh.itjust.works
      link
      fedilink
      arrow-up
      5
      ·
      1 year ago

      Not only the standard screw but a very effective head shape. The head is both self centring and can hold on the screw securely and without the use of magnets.

      • Welder@lemmy.ca
        link
        fedilink
        arrow-up
        7
        ·
        1 year ago

        I will die defending Robertson screw as a top contender. The rest of the world must learn our superior Canadian ways, by force if necessary.

        • TruckBC@lemmy.ca
          link
          fedilink
          arrow-up
          5
          ·
          1 year ago

          It’s 100% superior to anything else I’ve used. If you use a good quality screw driver or bit, they’ll NEVER strip, even using an impact driver.

    • cannedtuna@lemmy.world
      link
      fedilink
      arrow-up
      1
      ·
      edit-2
      1 year ago

      Lately I’ve seen a lot more Phillips Square, which is nice when you strip the fuck out of the Phillips head. Those are alright.

      • s_s@lemmy.one
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Pozidrive is basically a Robertson and Phillips on top of each other.

  • Gerowen@lemmy.world
    link
    fedilink
    arrow-up
    14
    ·
    1 year ago

    I hate phillips. It seems like their only purpose for existing is to strip out so that you can never remove them.

    Personally, any time I have a project, I always opt for torx (star). The screwdriver bits for them are not tapered so they don’t push themselves back out of the screw-head (unlike phillips), so they tend to stay in place and grip much better. It’s a lot harder to screw up a torx screw or bit than a phillips one.

    • snaf@lemmy.sdf.org
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      They actually were designed to cam out in low torque applications so consumers could not over-tighten them. The problem is now those consumers only know what a phillips is, so they’re used for everything.

    • flpasc@sh.itjust.works
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      I. Love. Torx! They just work! Don’t mind the angle, don’t mind the force! They’re just perfect! Never going back. (At least for everything related to woodworking)

    • tour_glum@sh.itjust.works
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      Same. I use torx for everything. Also gotta love the square Robertson ones, they’re just not common where I live. I hate Philips, although for anyone not aware, there is a difference between posi drive an Philips and going to the effort of making sure you have the correct one massively reduces torquing out and damage to screw head.

      • catshit_dogfart
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        IMO, phillips is for electronics and some small applications. Something you’re really not putting much pressure on and probably driving by hand and not a power tool.

  • HikingVet@lemmy.sdf.org
    link
    fedilink
    arrow-up
    10
    ·
    edit-2
    1 year ago

    Robertson, hex and torx should be on that list, the rest of that shit can stay in the scrap bin of designs