• rutellthesinful@kbin.social
    link
    fedilink
    arrow-up
    1
    ·
    9 months ago

    the one third of 9.5 conundrum, which was posed by a metric defender

    they weren’t a metric defender

    which is literally not true

    what scenario is there in your mind where you’d need a precision answer to what 1/3 of 9.5mm is, but also not have access to a calculator? and of those scenarios, how many of them would be solved by the knowledge that 1/3 of 1/8 is 1/24? i’m willing to bet the answer is more or less “none”.

    and for those that do exist, you can also get drafting rulers that give you 1/3rds of metric measurements.

    the accuracy of your equipment isn’t somehow better because you’re dealing with fractions rather than decimal points

    • bloodfart
      link
      fedilink
      arrow-up
      1
      ·
      9 months ago

      you’re right. the person who initially brought up 9.5 was comparing it to the sae equivalent 3/8 (9.525mm, but whos counting).

      Just wait for an American to tell you how it’s easier to use fractions with imperial. I’ve legit seen them say shit like 3/8 of an inch is easier to think about than 9.5mm.

      the reply was what i was thinking of, the obvious answer: “what if you need to divide by 3?”

      so good eye.

      one scenario when i’d want a precision answer to 1/3 of 9.5 but also not have immediate access to a calculator is when woodworking. you know, seeing as how 9.5 is (the actual metric defender this time’s approximation of) 3/8… and there’s no way that a calculator would help me there because the result of 9.5/3 is 3.16, a length i’d need at least tenth millimeter vernier calipers to accurately scribe. even 9.525/3 is 3.175, a measurement that requires um precision to scribe!

      the inch side of my ruler, however, is graduated in eighths of an inch and i can make that measurement easily with it.

      i’ve also used a third measurement of a known diameter when drilling holes in metal to use a technique described in machinerys handbook to cut slots.

      you were the one who asked what a third of an eighth was. i’m not sure why. why did you bring up a third of an eighth? was it because you thought it would allow a person to more easily answer the question what is 1/3 of 9.5?

      i guess my real question is this:

      how does a calculator help you make more accurate measurements?

      • rutellthesinful@kbin.social
        link
        fedilink
        arrow-up
        1
        ·
        9 months ago

        using a ruler to measure a length of 1/8" is as accurate as using a ruler to measure a length of 31mm and eyeballing 2/3 of a mm

        the bottleneck at that point is your eyeball and pencil lead, not the unit of measurement

        • bloodfart
          link
          fedilink
          arrow-up
          1
          ·
          9 months ago

          well, it’s 3.16 mm, not 31.6, but i get your meaning.

          in that case if you wanted to be real precise, you’d measure from the left or right side of one graduation to the same side of the next graduation. using that technique a person could get a better 1/8" off a ruler than someone eyeballing fractional mms would.

          I still don’t see how a calculator helps though.

          • rutellthesinful@kbin.social
            link
            fedilink
            arrow-up
            1
            ·
            9 months ago

            well yeah, because 1/8" is 3.175mm

            1/3 of a mm is a distance between 1/64" and 1/128"

            mechanical pencil lead is only about 0.4mm

            I still don’t see how a calculator helps though.

            don’t ask me ask the person who posed the “what’s a third of 9.5mm” question

            • bloodfart
              link
              fedilink
              arrow-up
              1
              ·
              9 months ago

              Usually when I’m making a precise line, I’ll put an edge on the pencil lead so it will make a mark thinner than its diameter.

              I seem to remember you as the one who brought up calculators, but I’m open to being mistaken.

              • rutellthesinful@kbin.social
                link
                fedilink
                arrow-up
                1
                ·
                9 months ago

                even if you’re in a situation where it’s somehow possible to manually draw 1/3 of a mm to any accuracy, 1/3 scale draft rulers still exist for metric, so it’s equivalent

                I seem to remember you as the one who brought up calculators

                because as soon as you have access to a calculator, “off the top of your head” is an irrelevance