• burnso@lemmy.world
    link
    fedilink
    English
    arrow-up
    7
    ·
    1 year ago

    I actually love it. It looks like something the character in question would have painted themselves.

  • Muttl3y@lemmy.world
    link
    fedilink
    English
    arrow-up
    4
    ·
    1 year ago

    I’m not really any good with paint but with finishing prints I’ve learnt a thing or two. High build primer and some fine wet and dry will make a huge difference covering up your layer lines.

    • Ready! Player 31@lemmy.worldOPM
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Thanks for the advice! I actually can’t see the layer lines with the naked eye unless the model is like three inches from my face.

      Maybe once I’m better at painting I’ll spend a bit of effort on this stuff but I think it’s okay for now.

      • Maple Engineer@lemmy.world
        link
        fedilink
        English
        arrow-up
        4
        ·
        1 year ago

        You may need reading glasses. I build RC helicopters which have very small mechanical parts. I can’t see any fine detail without reading glasses. I used to just buy them at my local drug store. They have a display with lots of different styles and magnification with text samples. You can try them on and read the text at arms length to figure out which ones work best for you. Also more light in your work area will probably help.

  • Apathy Tree@lemmy.dbzer0.com
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    Are the fingerprints on it intentional? They honestly look like decent texture design elements on most of it, to the point I had to go looking (the narrow top strip on the left hip piece told me they were fingerprints), so if they were intentional texture, disregard.

    If you want to avoid that (and the messy fingers) in the future, a plastic bottle cap and some blue tack/sticky tack/even tape helps a ton. Just adhere the mini to the bottle cap, and you have a way to hold it without risking the paint.

  • SSTF@lemmy.world
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    What types of paints are you using? There are tricks with cheaper paints, but even with good hobby paints, using a grey is always easier than white. The coverage will be more even and less transparent. Easier to freehand.

    It is easier to paint on the light grey first, then use white to highlight or to overpaint most of the center. If you miss a little with your white it won’t be noticeable.

      • Alteon@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        What’s your print height, temperature, bed temp, and material? And what’s your magical secret to get it to adhere without issues? The max I can get down to is 0.16mm and otherwise it just becomes a wispy mess if I go any thinner. You printing PLA?

        • Ready! Player 31@lemmy.worldOPM
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          Ah no this is resin! It prints at 0.05mm.

          I used to print in FDM but switched to resin earlier this year. There’s more chemicals faff with the resin and needing ventilation etc but you can print a plate full of these models in about four hours, wash and cure, and be done with it. I was printing a single model at a time on FDM and it took like six hours.

          • Alteon@lemmy.world
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            Wow…that quality difference is fucking massive. 0.05mm is three times better than I’m able to do right now.