Got an anycubic resin printer and I’m using their high speed resin (because it was bundled for free), and i tried to send a file using the high speed setting.

After the print it was seemed to be ok, then after i left in a bath of ethanol (IPA can’t be found in stores in my country) i got all those holes.

What’s the problem?

A slicer problem? The ethanol bath? The high speed resin that’s not good?

    • nikscha@feddit.deEnglish
      9·
      9 months ago

      To clarify: the issue is that the bad 3d moddel leaves you with very thin walls which get destroyed during the wash

      • Moonrise2473OPEnglish
        21·
        9 months ago

        the slicer said the model needed a repair (which it did), but then it also does this with other stuff. Later I try with a profile with more exposure time

        • nikscha@feddit.deEnglish
          2·
          9 months ago

          I see, but that just makes me want to blame the model even more.

          What can happen if you repair a bad model is that intersecting faces are merged in a way that leads to voids on the inside of your model. If that’s the case it’s really hard to fix for somebody who doesn’t have experience with pointcloud based 3d modeling.

          Please print something that you know is “good”, like the official 3d benchy. I’m almost certain it won’t have the holes that you’re experiencing on your part.

          Edit: do you have a link to the moddel? Then I can confirm for you whether the problem is with the mesh or not.

          • Moonrise2473OPEnglish
            2·
            9 months ago

            It was the resin. Once I bought a resin from another brand, it printed perfectly

            It really puzzles me why they would bundle 2 kg of low quality “high speed” resin that isn’t even able to correctly print the test files…

            • nikscha@feddit.deEnglish
              2·
              9 months ago

              Wow okay, definitely unexpected, but I’m glad you figured it out!

              Maybe the reseller just wanted to get rid of bad stock?

              • Moonrise2473OPEnglish
                1·
                9 months ago

                I noticed that that “high speed resin” was sold out even if they were still bundling it with new printers

                Then I realized that the profile for that resin in their own official slicer had half the vertical resolution and half the exposure time. It’s something broken that they created just for allowing the marketing to say “the fastest printer on the market, full prints in 2 hours instead of 8”. Even the demo file that was given with the resin had layer delamination when printed, and that’s the best use case, an empty cylinder that needs no support and has a constant wall thickness all around

  • eyes@lemmy.worldEnglish
    10·
    9 months ago

    Ethanol should be fine to use as far as I know. Do the holes go all the way through? If so your screen might have dead spots. You can visually inspect the screen by setting it to do a test exposure without the resin tank on it to check. Also obviously check that your tank doesn’t have any failed print bits stick to the sheet.

    • Moonrise2473OPEnglish
      5·
      9 months ago

      visual inspection of test exposure is ok, and then the vat is brand new so the sheet was immaculate

      • eyes@lemmy.worldEnglish
        6·
        9 months ago

        Is this the first print you’ve done with it? Have you done any exposure calibration with this resin?

        • Moonrise2473OPEnglish
          3·
          9 months ago

          first print with the printer and first print with resin in my life

          The manual didn’t mention the exposure calibration at all…

          • eyes@lemmy.worldEnglish
            8·
            9 months ago

            It’s probably under exposed then. Something like this and this will help you tune your slicer settings. You might need to play with other settings if you have other issues, but most of the time the exposure settings will be the problem with new resins.

            • PipedLinkBot@feddit.rocksBEnglish
              21·
              9 months ago

              Here is an alternative Piped link(s):

              this

              this

              Piped is a privacy-respecting open-source alternative frontend to YouTube.

              I’m open-source; check me out at GitHub.

  • plandeka@lemmy.worldEnglish
    7·
    9 months ago

    They look like air bubbles to me, but it is weird they only come out after the bath. Could be they were already inside, but only covered by a thin wall of resin.

    I usually use Isopropanol for bath not Ethanol, so I am not sure how your resin reacts with that. The bath should also be rather short, like 1min or something.

    A few things to try:

    • If you are shaking your resin before print, then give it like 10 minutes after you pour it into the vat, so all bubbles come out and pop
    • lower the print speed
    • add wait times between the end of lowering the plate and light on
    • try to hollow out the model if possible, so there is less printing volume
  • nothacking@discuss.tchncs.deEnglish
    3·
    9 months ago

    It has nothing to do with the ethanol, the uncured resin simply covers the surface and fills small holes, hiding them

    I would guess it’s something funny with the 3d model, air bubbles in the tank wouldn’t be consistent between layers. Try inspecting the problematic layers on your slicer.

    Almost looks like the slicer might be trying to add FDM style infill, make sure it is not.