Hi! New to the community, new to 3d printing, new to all of this.

I am heavily considering the Prusa Mini as my first printer.

  • Want a brand that is a good citizen in the 3d printing community and Prusa seems to be on this list.
  • Want a high quality printer to begin my adventure with that doesn’t leave me guessing if it’s my lack of skill or a lack of quality hardware.
  • Want open design to enable to tweak and improve the hardware/software as I see fit.
  • Linux user who wants full Linux support in the software stack.
  • I want to spend as little as possible on my first printer (still want high quality) because I see myself spending a lot more fairly quickly if I enjoy this as much as I suspect I will. Fortunately I can spend what I need to meet my current requirements but keeping cost down as much as possible is the goal.
  • Enjoy tinkering with hardware and software. Have a background in electronics and Linux system administration.

Would you agree that the Prusa Mini is a good starting spot considering the above?

The pricing I see in reviews etc seems to be lower then what is currently being offered on the Prusa site. Do they often have sales or specials or is this just because the cost of production has gone up? I see reviews that indicate a price of $349 but it’s going for $429 on the Prusa site currently.

Should I consider adding the filament sensor and any extra build sheets? Filament from them or elsewhere?

Anything I am missing or not considering?

Any and all feedback is welcomed! Thanks ahead of time!

  • Sticky@lemmy.worldEnglish
    22·
    1 year ago

    I have no experience with the Prusa mini, but as a first timer, I found the Ender 3 (pro, I think) perfectly good quality. It might be due to lack of experience with anything else, so if definitely defer to folks who have experience with a few different models, but I’ve found it good for all of my printing needs (Cases, utility objects, and the occasional figurine/trinket). If that success is anything out of the ordinary, I think I’d attribute it to a few things…

    • I followed a really detailed setup/assembly guide from a YouTube channel about 3d printing miniatures ( I can probably find it again if you’d like, it was highly recommended)
    • I got firmer springs for the print bed (sometimes I go hog wild printing things, sometimes it sits for months, I can’t remember them last time I had to level the bed)
    • I got a glass print surface.

    I was generally in the same boat as you; Liked to tinker, and wanted the best quality but didn’t want to pay out the ass for it. I typically tend to “overspend” when getting into a new hobby out of the fear I won’t stick with it if I struggle with low quality gear, bit also have an aversion to parting with my cash. These upgrades seemed to be the consensus reached at the time for how to get good consistent results out of the Ender 3.

    I find the Ender 3 to be occasionally too small for things I want to print, but generally a good size, and look forward to being able to tinker further with an upgraded/quieter main board.

    So, all in all, I can’t help with anything specific to the Prusa mini, but can vouch for the Ender 3 as fitting my needs when I think I had the same general quality/cost criteria as you. Hope you found this helpful! Good luck in your printer search!

    • franzfurdinand@lemmy.worldEnglish
      6·
      1 year ago

      The Ender 3 Neo comes out of the box with a bed leveler - that’s pretty much my go-to recommendation for someone getting started.

      • cryball@sopuli.xyzEnglish
        2·
        1 year ago

        A couple of months ago I bought an ender 3 neo as my first printer. I haven’t been disappointed with it.

        I spent ~200€ on my neo. I didn’t go for the v2 neo, as I didn’t feel like the extra features were worth it. Tensioning the belts by hand is not difficult and the glass bed has super good adhesion so far. If the prints are stuck to the bed, I usually put the glass into a freezer for 15min and the prints pop off easily.

        The setup before printing was like 1h of assembly and 20 minutes to level the bed and set z offset.

    • solarbird@kbin.social
      4·
      1 year ago

      Yeah, if you actively like to tinker, the Ender 3 series will give you every opportunity. And sometimes will require it. xD (My 3V2 hasn’t really required it, but holy shit is it not stock anymore and I have learned a lot making it that way.)

      Seriously though, the Ender 3 community and mods availability is unsurpassed. These things are truly the Model T of printers for both better and worse, and I’m glad I started here, it’s been educational as hell and that’s part of what I wanted. And it’s a bit of a hotrod at this point! Because I made it so. :D